（1）无线AP设置
以下设置时
一、给AP设定管理地址
interface BVI1
ip address 192.168.0.112 255.255.255.0
no shut
二、设定SSID
dot11 ssid 1042N //1042N即是终端收到的信号的名字
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii XXXXXX //XXXXXX表示密码
三、在接口下启用加密方式并应用SSID
interface Dot11Radio0
encryption mode ciphers aes-ccm tkip
ssid 1042N
no shut
-----------------------------no shutdown后提示-------------------------------------
ap(config-if)#no shut
ap(config-if)#
*Mar 1 01:22:03.254: %DOT11-6-FREQ_SCAN: Interface Dot11Radio1, Scanning frequencies for 21 seconds
*Mar 1 01:22:03.261: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 01:22:03.261: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 0 due to not using AES encryption or encryption is not disabled
*Mar 1 01:22:24.772: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5785 selected
*Mar 1 01:22:24.773: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 0 due to not using AES encryption or encryption is not disabled
*Mar 1 01:22:24.773: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 01:22:25.773: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
-----------------------------no shutdown后提示-------------------------------------
interface Dot11Radio1
encryption mode ciphers aes-ccm tkip
ssid 1042N
no shut
四、查看连接AP的用户
ap#show dot11 associations
802.11 Client Stations on Dot11Radio0:
SSID [1042N] :
MAC Address IP address Device Name Parent State
0024.2ce8.0231 192.168.30.249 ccx-client - self Assoc
（2）胖AP上多个SSID配置脚本
hostname AP1
dot11 vlan-name hdoffice vlan 1
dot11 vlan-name harley-davidson vlan 10
dot11 ssid hdoffice
vlan 1
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii adminhalei #### 认证密钥
exit
dot11 ssid harley-davidson
vlan 10
authentication open
authentication shared
mbssid guest-mode
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm tkip ## 启用wpa2认证
mbssid
ssid hdoffice
ssid harley-davidson
station-role root access-point
no shut
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
exit
interface Dot11Radio0.10
encapsulation dot1Q 10
bridge-group 10
interface Dot11Radio1
encryption vlan 1 mode ciphers aes-ccm tkip
mbssid
ssid hdoffice
ssid harley-davidson
no shut
interface Dot11Radio1.1
encapsulation dot1Q 1 native
bridge-group 1
exit
interface Dot11Radio1.10
encapsulation dot1Q 10
bridge-group 10
int gi0
no shut
exit
int gi0.1
encapsulation dot1q 1 native
bridge-group 1
exit
int gi0.10
encapsulation dot1q 10
bridge-group 10
exit
int bvi
ip add 192.168.1.201 255.255.255.0
no shut
exit
ip default-gateway 192.168.1.1
发表评论 评论 (9 个评论)
dot11 mbssid
Use the dot11 mbssid global configuration command to enable multiple basic SSIDs on all access point radio interfaces.
[no] dot11 mbssid
--------------------------------------------------------------------------------
Note This command is supported only on access points that contain at least one radio interface that supports multiple basic SSIDs. To determine whether a radio supports multiple basic SSIDs, enter the show controllers radio_interface command. Multiple basic SSIDs are supported if the results include this line:
Number of supported simultaneous BSSID on radio_interface: 8
--------------------------------------------------------------------------------
Syntax Description
This command has no arguments or keywords.
Defaults
This command is disabled by default.
Command Modes
Global configuration
Command History
Release
Modification
12.3(4)JA
This command was introduced.
Examples
This example shows how to enable multiple basic SSIDs on all interfaces that support multiple basic SSIDs:
ap(config)# dot11 mbssid